Введение
Солнечный EPC, который пишет galvanized steel, 25-year life в RFQ трекера, получит три несравнимых предложения. Стан котирует непрерывный рулон EN 10346 ZM на C-прогоны. Цех котирует ISO 1461 после изготовления сварных свай. Третий подставляет DX51D+Z, потому что появилось слово galvanized. Текучесть может совпасть с чертежом. Химия покрытия нет.
Это руководство по траектории службы для импортеров, которые покупают сталь трекера в Китае: холодногнутые профили из рулона и сварные сваи или кронштейны, которым все еще нужен цинк после резки. Это не замена заказанной редакции EN 10346, ISO 1461, ASTM A123, ASTM A1046, JIS G 3323 или ISO 9223. ZAM, Magnelis, PosMAC и SuperDyma это покрытия станов, а не взаимозаменяемые марки. Зафиксируйте стандарт, обозначение и форму продукта до сравнения FOB.
Классифицируйте площадку до того, как назовете покрытие
Сначала классифицируйте солнечную площадку по ISO 9223, затем разделите ведомость материалов. Холодногнутые прогоны обычно идут на рулон EN 10346 ZM. Сварные сваи и толстые кронштейны обычно идут на ISO 1461 или ASTM A123 HDG после изготовления. ZM120 не заменяет 85 um последующего цинкования.
ISO 9223 / ISO 12944-2 is the duty. The mill already has zinc-coated coil. Batch HDG is an extra shop after welding. If the RFQ only writes GI or HDG, the cheapest photographable path wins.
| Класс площадки | Типичная установка трекера | Путь рулона | Путь изготовленной секции |
|---|---|---|---|
| C2–C3 | Inland, low chloride | EN 10346 ZM on structural coil, often ZM120–ZM275 | ISO 1461 or ASTM A123 after fabrication if the part is welded |
| C4 | Industrial belt or coast beyond about 1 km | Raise ZM mass; ZM275–ZM310 is a common RFQ band | Mean coating thickness on the finished thickness, not a coil Z code |
| C5 | Severe coastal, about 150 m class talk | ZM alone is often not a 25-year standalone story | Batch HDG after all cutting and welding, with sealed edges if coil is still used |
Manufacturer design-life tables for one Type 2 Zn-Al-Mg coating (ZM310 / ZM430) are often quoted as C3 30 to >50 years, C4 15-30 years, and C5 8-15 years for ZM310. Those bands are mill data. They are not a generic ZM guarantee and they exclude soil or standing-water contact. A USD 40 per tonne gap on 2.5 mm purlin coil is often this missing class. ZM120 coil is not comparable with 85 um batch HDG on 8 mm pile.
Разделите сталь трекера по форме: холодногнутый рулон против изготовленной секции
Product form decides the process. Continuous coating happens on strip before the profiler. Batch HDG happens on the finished part after cutting, punching, and welding.
| Элемент трекера | Обычная форма | Подходящее покрытие | Почему замена ломается |
|---|---|---|---|
| C-purlin, U-channel, cold-formed girder | Coil, typically 1.5–3.2 mm | EN 10346 +ZM on a structural grade | Batch HDG after roll-forming is slow, distorts thin gauge, and is the wrong shop |
| Torque tube from strip | Coil or tube from coated strip | ZM coil if the weld is re-protected; HDG if the tube is welded from black steel | A black weld on ZM coil is a bare cut until it is repaired |
| Driven pile, H-pile, thick bracket, shop-welded frame | Plate or section, often ≥6 mm | ISO 1461 or ASTM A123 after fabrication | ZM coil cannot wrap a shop weld; cut edges on thick plate are not a 2 mm self-heal story |
Оцинкованный рулон DX51D это непрерывный цинк формовочной марки. Прогонам с классом текучести нужно фиксировать S350GD или S550GD, а не прозвище DX51D. Оцинкованный рулон G550 это высокопрочный цинк для кровли; химия остается +Z, если PO не пишет +ZM. SGCH это твердый рулон, не конструкционная марка трекера. Оцинкованная балка H это путь изготовленной секции. Углеродистый плоский прокат это черный лист, который затем идет в котел HDG. Не смешивайте эти строки в одной ячейке GI tracker.
Когда рулон EN 10346 ZM подходит под задачу
ZM / Zn-Al-Mg is a continuous coating. EN 10346 writes it as ZM mass in g/m2 both sides. ASTM A1046 covers Zn-Al-Mg sheet and names types. JIS G 3323 is the Japanese sheet standard. No document makes two mill baths 100% equivalent.
| Coating family | Standard buyers name | Chemistry on mill sheets | Number that must be printed |
|---|---|---|---|
| Zn-Al-Mg coil | EN 10346 +ZM; ASTM A1046; JIS G 3323 | Zinc with aluminium and magnesium. One Type 2 bath is often described as about 3.5% Al and 3% Mg. Other baths run higher aluminium. | ZM120, ZM275, ZM310, ZM430 as total both-sides mass |
| Continuous zinc coil | EN 10346 +Z; ASTM A653 | Essentially zinc | Z275 as total both-sides mass |
| Batch HDG | ISO 1461; ASTM A123 | Zinc bath, typically high-purity zinc | Mean and local-minimum thickness in μm on the finished part |
Coating density is mill-specific. One Type 2 producer publishes 6.2 g/cm3 and lists ZM120 about 10 um per side, ZM310 about 25 um, ZM430 about 35 um. Other catalogues use about 6.0 g/cm3. Do not convert a competitor ZM310 with zinc density 7.1 g/cm3 and call it equal to 85 um batch HDG. Substrate chemistry is a separate table. Confirm the ordered EN 10346 edition; typical maxima, not the heat on your dock:
| Grade | C % max | Si % max | Mn % max | P % max | S % max | Yield min (MPa) | Tensile min (MPa) | A80 typical table |
|---|---|---|---|---|---|---|---|---|
| S350GD | 0.20 | 0.60 | 1.70 | 0.10 | 0.045 | 350 | 420 | 16 |
| S550GD | 0.20 | 0.60 | 1.70 | 0.10 | 0.045 | 550 | 560 | 12 |
| DX51D | 0.18 | 0.50 | 1.20 | 0.12 | 0.045 | — (forming grade) | 270–500 band commonly discussed | 22 |
S350GD and S550GD are structural coating grades. DX51D is not a yield class. Shipping DX51D+Z against S350GD+ZM310 changes chemistry and the mechanical contract. Cut-edge talk on thin strip: Al and Mg help a dense film over a sheared edge. One German Type 2 approval uses ZM120 or higher up to 1.5 mm, ZM250 or higher up to 3.0 mm, ZM310 or higher above 3.0 mm. ZM coil fits roll-formed 1.5-3.2 mm members, mill edge rules, class plus mass together, and named weld re-protection, not hope that self-heal covers a 6 mm weld.
Когда HDG после изготовления безопаснее
Batch HDG coats the part you install. Cutting, drilling, and welding happen on black steel. Thick piles and shop-welded frames still go to ISO 1461 or ASTM A123 even when purlins are ZM coil. Common ISO 1461 minima for articles not centrifuged (confirm edition):
| Steel thickness t | Local min (um) | Mean (um) |
|---|---|---|
| t ≥ 6 mm | 70 | 85 |
| 3 mm ≤ t < 6 mm | 55 | 70 |
| 1.5 mm ≤ t < 3 mm | 45 | 55 |
| t < 1.5 mm | 35 | 45 |
ASTM A123 uses coating grades by steel thickness and often lands thicker on heavy sections than the ISO 1461 mean. Do not treat 85 um and ASTM A123 as the same cell. Fabricated HDG substrate is usually carbon plate or section, not S350GD coil. Buyers still discuss S355JR / Q355B / A36 families for piles. Typical thinner-plate S355JR talk: C 0.24% max, Mn 1.60% max, P and S 0.035% max, yield 355 MPa at t <= 16 mm. Batch HDG belongs when the member is shop-welded, thicker than purlin coil, C5 with an insurance file, or in soil. Do not send 2.0 mm C-purlins to the kettle. Do not send 12 mm welded piles as ZM coil.
Масса покрытия, марка подложки и кромки, которые дисквалифицируют оферту
These are disqualifiers, not preferences.
| Пустое поле | Что отправит стан | Правило удержания |
|---|---|---|
| Site class | C3 coil against a C5 drawing | No award until ISO 9223 / ISO 12944 class is on the PO |
| Product form | One GI price for purlins and piles | Split the bill: coil ZM vs batch HDG |
| Coating designation | Z275 against a ZM310 line, or ZM120 against 85 μm | Coating family and number must match the member |
| Substrate grade | DX51D or SGCH against S350GD / S550GD | Mechanical class must be printed |
| Thickness and tolerance | ”2.5 mm GI” | Thickness, EN 10143 class or mill tolerance, width, coil ID |
| Cut-edge / perforation rule | Dense punching on 3 mm ZM120 | Mass vs thickness rule from the named mill, or switch that part to HDG |
| Fasteners | Standard HDG bolts on a C5 tracker | Fastener coating is its own line; C5 often needs zinc flake or A4-316L with isolation |
| Weld repair on coated tube | Bare HAZ | Named re-protection thickness |
Dimensional band actually shipped for tracker coil, mill confirmation required: thickness 1.5-3.2 mm for purlins; width as developed profile, often 200-600 mm slit from 1000-1250 mm parent coil; ID 508 mm or 610 mm; slit coil weight 3-8 MT. Name EN 10143 class or a mill mm band. +/-0.05 mm is a commercial extra. ZM passivation is chromate-free film or oil. Temporary storage, not the 25-year layer. Write dry / oiled / chemical passivation.
Что должны доказать MTC и PSI до выхода контейнера
The first warning is a PI that wrote GI tracker steel, 2.5 mm. Floor pattern: PI writes galvanized, 2.5 x 250, S350, 25-year. Coil tag is DX51D+Z275. Pile pack is still black H-beam. PSI photographs spangle. Missing ZM mass and ISO 1461 mean thickness never enter the report. Check практику документации EN 10204 3.1 before booking a profiler or kettle. ZM is not +Z. +Z is not ISO 1461. ISO 1461 is not ASTM A123. Coil: g/m2 both sides as ZMxxx. Fabricated: um mean and local min. S350GD is not DX51D. S355JR plate is not S350GD coil. Heat number on tag, packing list, and EN 10204 3.1 MTC. Coil packing: VCI paper, film, metal edge rings, at least 3 circumferential and 4 radial straps. Eye-to-sky or eye-to-wall. A 20GP still lands near 25-28 MT. Tell SGS, BV, or TUV to photograph tags and thickness spots. If the mill says ZM120, Z275, and 85 um HDG are equivalent because all three are zinc, ask for standard, mass or mean thickness, and product form on the same page as yield. Keep these contract numbers on the same page as yield: EN 10346, EN 10143, EN 10204 3.1, ISO 1461, ISO 9223, ISO 12944-2, ASTM A123, ASTM A1046, ASTM A653, JIS G 3323, ZM120 ZM275 ZM310 ZM430 Z275, density 6.2 g/cm3 or 6.0 g/cm3 not 7.1 g/cm3 zinc, about 10 um / 25 um / 35 um per side on one Type 2 mill, ISO 1461 70/85 um at t >= 6 mm, 1.5-3.2 mm purlins, 2.0 mm C-purlin distortion, 2.5 x 250 tag, 8 mm pile, 12 mm welded pile, 16 mm yield basis, slit 200-600 mm from 1000-1250 mm parent, ID 508 mm or 610 mm, 3-8 MT slit coils, 25-28 MT per 20GP, 7-15 days, S350GD 0.20/0.60/1.70/0.10/0.045/350/420/16, S550GD 550/560/12, DX51D 0.18/0.50/1.20/0.12/270-500/22, S355JR talk C 0.24 Mn 1.60 P/S 0.035 yield 355 MPa, +/-0.05 mm extra, 3.5% Al, 150 m C5 talk, 25-year sentence, not 100% equivalent, A36 family, A4-316L fasteners, WhatsApp +86 151 5311 2221.
Строки RFQ, которые отделяют рулон ZM от партионного HDG
Copy after the bill of materials. Fasteners, pile soil, and earthing stay separate lines.
Roll-formed members (coil)
- Standard: EN 10346 (ordered edition) +ZM, or ASTM A1046 type named, or JIS G 3323.
- Grade: S350GD or S550GD. Not DX51D unless commercial quality is truly the duty.
- Coating: ZM310 (example). Both sides. Actual mass on the MTC.
- Thickness x width; EN 10143; ID 508 or 610 mm.
- Surface: chromate-free passivation or oil.
- Mill edge rule for punched holes.
- Certificate: EN 10204 3.1 with heat, chemistry, yield/tensile/elongation, coating mass, designation.
- Packing: VCI + film + rings + 3 circumferential / 4 radial.
Fabricated members (batch HDG)
- Black steel: S355JR / specified plate or section; size; named WPS.
- Galvanizing: ISO 1461 or ASTM A123, ordered edition. Mean and local min for actual thickness.
- Kettle after all cutting, drilling, welding.
- Certificate: EN 10204 3.1 plus galvanizer thickness spots.
- Packing: bundle separators, no wet stacking.
Coil trial MOQ remains 1 x 20GP (25-28 MT) on standard slit sizes.
Заключение
ZM coil and batch HDG are two answers to two tracker jobs. Classify the site, split the bill, freeze the standard and the number, then read that number on the MTC. A 25-year sentence without class, form, and coating designation is not a specification.
Планируете заказ или нужна техническая проверка?
Если вы закупаете конструкционный рулон с покрытием ZM или секции трекера партионного HDG и нужно сверить строку покрытия с ведомостью:
- Быстрое техническое коммерческое предложение: пробные заказы от 1 x 20GP (25-28 MT) с отгрузкой за 7-15 дней для стандартных размеров рулона. Отправьте обозначение (ZM или ISO 1461 / ASTM A123), марку, толщину и количество через онлайн-форму RFQ.
- Обеспечение качества: каждый заказ сопровождается подлинными EN 10204 3.1 Mill Test Certificates с прослеживаемостью плавки. Инспекции SGS, BV, TUV приветствуются.
- Срочные запросы: экспортный стол в Шаньдуне в WhatsApp +86 151 5311 2221.
